Small Run BHO Technique - Page 26

Blckmagc88 · 09-28-2011, 07:24 PM

as to the issue of pressure loss on the maglite I just like "caulked" around the butane adapter tip with "shoe goo"(skaters know what this is) and it holds the adapter tip in there nice and firm.

Detective Dank · 09-29-2011, 02:22 PM

that sounds terrible. how can you be sure butane isnt contacting and then extracting crap from the shoe goo if thats what's ultimately preventing the pressure loss?

Blckmagc88 · 09-29-2011, 04:51 PM

I mean I'm not a scientist or anything but I'm still here typing so...seems like its working to me. Can't be worse then the 20 effin cigs I smoke daily right? Thats got rat poison in it for god sake. me

Detective Dank · 09-29-2011, 05:17 PM

why not just spend 4 dollars on a stainless steel turkey baster and know that your vessel isn't leaking, or leeching harmful chemicals? or at least buy a new maglite/figure out a way of sticking the adaptor tip in? I use rolling paper to make sure the tip is sealed: rolling paper is less than .001 of an inch thick, so you can add layers to ensure its sealed. I used to use plumbers/teflon tape, but I got worried about extracting crap from the teflon, but even that would be better than any glue related substance. edit: at least the teflon is meant to be used on your pipes for drinking water!

ineedmyham · 10-07-2011, 05:28 AM

Quote:

Originally Posted by Detective Dank

I use rolling paper to make sure the tip is sealed

sick, I will have to try this,this is a great tip, as I have been thinking the same thing about teflon tape, although it works well.

Detective Dank · 10-08-2011, 02:10 AM

Yep, it works surprisingly well. It bunches up and makes the same little white (well in this case hemp coloured as i use hemp papers) circle donut a majigger around the extractor tip that keeps the seal solid. Just be carefull when repeatedly pulling the can in and out of the tip as that may pop it loose, as the paper isn't stickyish like teflon tape and make sure you check the tip every run to see if its still solid. I always make sure to give it a final shove in before I start spraying.

Pillowpants · 10-14-2011, 05:51 PM

dumb question... whats the most effective way to shorten a turkey baster, just take a saw to it? what length should I cut it to fit roughly a quad to 9g's

MesaBoogieMan · 10-14-2011, 06:47 PM

Pipe cutter..... Makes a clean cut w/o crushing the baster

Kush&OJ · 10-14-2011, 10:26 PM

Hack saw with just a strong pipe cutting wire I've cut about three, all different lengths

Dan K · 10-16-2011, 05:07 PM

Used this to cut about 3" off my baster. Worked PERFECT in less then a min and cost less then 10 bucks at my hardware store!

The full baster holds about 24, cut one holds around 14.

just got this lil guy... we shall see.

09-28-2011, 07:24 PM	#251
Blckmagc88 New Member Join Date: May 2010 Posts: 19	as to the issue of pressure loss on the maglite I just like "caulked" around the butane adapter tip with "shoe goo"(skaters know what this is) and it holds the adapter tip in there nice and firm.
Blckmagc88 New Member Join Date: May 2010 Posts: 19

09-29-2011, 04:51 PM	#253
Blckmagc88 New Member Join Date: May 2010 Posts: 19	I mean I'm not a scientist or anything but I'm still here typing so...seems like its working to me. Can't be worse then the 20 effin cigs I smoke daily right? Thats got rat poison in it for god sake. me
Blckmagc88 New Member Join Date: May 2010 Posts: 19

10-14-2011, 05:51 PM	#257
Pillowpants Member Join Date: May 2011 Location: Texas Posts: 116	dumb question... whats the most effective way to shorten a turkey baster, just take a saw to it? what length should I cut it to fit roughly a quad to 9g's
	"A Life Without Knowledge is Death in Disguise"

10-16-2011, 05:07 PM	#260
Dan K HIGHER Standard Join Date: Nov 2010 Posts: 874	Used this to cut about 3" off my baster. Worked PERFECT in less then a min and cost less then 10 bucks at my hardware store! The full baster holds about 24, cut one holds around 14. just got this lil guy... we shall see.
Dan K HIGHER Standard Join Date: Nov 2010 Posts: 874

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-29-2011, 02:22 PM	#252
Detective Dank Senior Member Join Date: Jun 2009 Location: Toronto Posts: 581	that sounds terrible. how can you be sure butane isnt contacting and then extracting crap from the shoe goo if thats what's ultimately preventing the pressure loss?

09-29-2011, 05:17 PM	#254
Detective Dank Senior Member Join Date: Jun 2009 Location: Toronto Posts: 581	why not just spend 4 dollars on a stainless steel turkey baster and know that your vessel isn't leaking, or leeching harmful chemicals? or at least buy a new maglite/figure out a way of sticking the adaptor tip in? I use rolling paper to make sure the tip is sealed: rolling paper is less than .001 of an inch thick, so you can add layers to ensure its sealed. I used to use plumbers/teflon tape, but I got worried about extracting crap from the teflon, but even that would be better than any glue related substance. edit: at least the teflon is meant to be used on your pipes for drinking water!

10-08-2011, 02:10 AM	#256
Detective Dank Senior Member Join Date: Jun 2009 Location: Toronto Posts: 581	Yep, it works surprisingly well. It bunches up and makes the same little white (well in this case hemp coloured as i use hemp papers) circle donut a majigger around the extractor tip that keeps the seal solid. Just be carefull when repeatedly pulling the can in and out of the tip as that may pop it loose, as the paper isn't stickyish like teflon tape and make sure you check the tip every run to see if its still solid. I always make sure to give it a final shove in before I start spraying.

10-14-2011, 06:47 PM	#258
MesaBoogieMan Ya(b)-a-Dab-will-do Join Date: Jul 2011 Location: Squeezing your mind grapes Posts: 1,962	Pipe cutter..... Makes a clean cut w/o crushing the baster